Primera LX200 Manuel d'utilisateur

User's Manual© 2008 All rights reserved080508-511203-(01)(Label Printer 200)511203.qxd 8/7/2008 2:20 PM Page i

6 Hardware and Software SettingsIf you are using a PC, after a few moments, Windows will tellyou it has found new hardware and is looking for software

Hardware and Software Settings 7D. INSTALLING LABEL STOCKYour printer will utilize a wide variety of paper label stock. As long as the label stock is

8 Hardware and Software Settings5. Place the leading edge of the label stock between thethroat guide and the side of the printer.6. Feed the label s

Hardware and Software Settings 9E. ADJUSTING THE LABEL STOCK TOF (TOP OF FORM) SENSORIf you are using label stock other than standard square / rectang

10 Hardware and Software SettingsThrough Hole LabelsIf you are using card stock or label stock that has a hole punchor a notch to identify a transitio

Hardware and Software Settings 11To adjust the sensor position use a pen to move the slide bar tothe correct postion.F. USING FAN-FOLD LABEL STOCKIt i

12 Hardware and Software SettingsG. INSTALLING THE INK CARTRIDGEYour printer has a built-in ink tracking system. This system isdesigned to warn you i

Hardware and Software Settings 1311. Push cartridge cover downward until it snaps in place.12. Click OK on your screen to indicate the new cartridge i

14 Hardware and Software Settingsc. Cut or fold a 8.5" x 11" sheet of paper in half length wise sothat it is no wider than 4.25 inches. Pul

Printing Using a PC 15Section 3: Printing Using a PCA. USING NICELABELYour printer ships with a basic version of Niceware's NiceLabelsoftware. T

iiNotices: The information in this document is subject to change without notice. NO WARRANTY OFANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDIN

16 Printing Using a PCb. Select your printer. This should be the Label Printer200. Click Finish. 3. Now you will see your label in the Document Win

Printing Using a PC 174. Now, insert a barcode.a. Click the Barcode Tool Icon from the Toolbox. You willnow have a Barcode Cursor that can be positio

18 Printing Using a PCb. The first screen in the Barcode Wizard will allow youto select the type of Barcode you wish to print. Youcan also enter the

Printing Using a PC 195. Now insert a graphic. Click on the Graphics Tool Icon inthe toolbox. You will now see a Graphics Cursor. Drag thecursor to

20 Printing Using a PCb. There are other tools at your disposal to align theobject or add shapes. On the right side of the screenyou will see alignme

Printing Using a PC 21B. CREATING BARCODES IN NICELABELa. Click the Barcode Tool Icon from the Toolbox. b. You will now have a Barcode Cursor that ca

22 Printing Using a PCiii. This contains four tabs, General, Check Digit, HumanReadable and Details.iv. The General Tab allows you to choose the appro

Printing Using a PC 23When you change the barcode dimension directly from thescreen by moving the drag handle, the changed dimensionwill also appear i

24 Printing Using a PCC. PRINTER DRIVER SETTINGSOnce the printer driver has been successfully installed, youwill need to setup the driver with the app

Printing Using a PC 25NOTE on PC Settings: Most applications allow you to change these same printer driveroptions from their "Print" and/or

iiiTable of ContentsSection 1: Getting Started...1A. Choosing a Good Locat

26 Printing Using a PCInk SaturationThis option controls the amount of ink used when printing animage. The default setting is 100%. If the ink is no

Printing Using a PC 27Note: You will be prompted to load label stock of 4"x 4" (101.6 mm x101.6mm) or larger, into the printer. If you have

28 Printing Using a PCSensor TypeSensor Type refers to the method the printer will use to detectthe print starting position for each label. If you ar

Printing Using a PC 29Enable Bi-di PrintingThis setting defaults to Yes for fastest printing. When enabledyou will be required to perform an alignmen

30 Printing Using a PCTop of Form (TOF)This setting allows you to fine tune the print starting positionon your label stock. This will be factory cali

Troubleshooting 31Section 4: Troubleshooting A. SOLVING REGISTRATION PROBLEMSImage is Vertically OffsetThe LX200 decides where to start printing by de

32 Troubleshooting2. Nonstandard / Non-translucent Backing Material. Test theunit with the label sample material that came with the unit.If it prints

Troubleshooting 33Note: Often times a space on the right (printers left) side indicates a margin around the label that is not being accounted for. The

34 TroubleshootingB. CREATING A FULL BLEED PRINT1. If you are having trouble making the image cover theentire label, first make sure the image is pri

Troubleshooting 35C. CLEARING A LABEL JAMIf there is a label jam in the printer mechanism first attempt toremove the jam by opening the cover and remo

ivInteractive Feature in this PDF DocumentThere are interactive features that will allow you tojump to different locations within the document. Eachli

36 TroubleshootingE. CLEANING THE INK CARTRIDGEIt may be necessary to clean the ink cartridge nozzles if younotice reduced print quality, or if you su

Label and Roll Specifications 37Section 5: Label and Roll SpecificationsMax MinLabel/Print width 4.25" (108mm) 0.75" (19mm)Liner width 4.25

38 Label and Roll SpecificationsMax MinDistance from edge of 1.90" (48.3mm) 0.20" (5.1mm)media to edge of thru-holeReflective/Black Equal

Technical Specifications 39Section 6: Technical SpecificationsPrint Method: InkjetPrint Resolutions: 4800 x 1200 dpi, 1200 x 1200 dpi, 600 x 600 dpi

40 IndexIndexBarcode Wizard...17, 18, 21Cartridge Alignment ...

Printed in the United States of AmericaP/N 511203511203.qxd 8/7/2008 2:22 PM Page 44

Getting Started 1Section 1: Getting StartedTHANK YOU…...for choosing an LX200 Label Printer. The LX200 Printer willprint razor-sharp text and barcod

2 Getting StartedB. UNPACKING AND INSPECTIONWhile unpacking your printer, inspect the carton to ensure that no damage has occurred during shipping. M

C. IDENTIFYING THE PARTSThis illustration shows the front of the printer with its controlbuttons and LED indicator lights.The Pause Button pauses the

4 Getting StartedThis illustration shows the input ports and power switch foundon the rear panel of the printer. D. COMPUTER SPECIFICATIONSMinimum PC

Hardware and Software Settings 5Section 2: Hardware and SoftwareSetupA. INSTALLING THE PC SOFTWAREThe Installer Disc has a menu that will guide you t